Complete PCB design and Firmware for RF transmitter and reciever

Closed Posted 4 years ago Paid on delivery
Closed Paid on delivery

RF Receiver:

434,000 MHz

2 Channel Wireless Receiver

9 – 32VDC Operating Voltage

Positive Output (Latched until Negative unlatch received)

Unlatch Negative input

Negative Output Channel 1 (Momentary) 2A

Negative Output Channel 2 (Momentary) 2A

Built in Buzzer (Buzzer signal when RF signal received, NO SIGNAL if LATCH ON)

Buzzer Specs: PCB Mount; 3500Hz; >90dB;

Learn Button ( PCB mount button )

Pair up to 50 individual transmitters

RGB Status LED

Should be resistant against irradiated and induced electro-magnetic noise

Learn Mode should reduced range to 50cm.

Transmitter Low Battery LED.

Low Battery LED should illuminated if last received transmitter battery is low.

All inputs and outputs should include short circuit protection, over current protection, reverse polarity protection.

Connector specifications will be supplied.

PCB Size limitations: Width 55mm, 45mm usable. Length <80mm

more details will be shared in the inbox

Electronics PCB Layout Circuit Design Embedded Software Microcontroller

Project ID: #22393230

About the project

9 proposals Remote project Active 4 years ago

9 freelancers are bidding on average $243 for this job

amelectronics

Hello sir, I have experience in designing electronics circuits and can develop hardware compatible smartphone and PC based apps. I also have done a lot of IoT projects and can transform your idea into a fully working p More

$500 AUD in 20 days
(53 Reviews)
6.8
mechatronicsengr

Hi, I hope you are doing well. I have expertise in RF based embedded projects. I have understood your requirements. I would to ask few questions. Please send me message for further discussion. Looking Forward, Khawa More

$300 AUD in 7 days
(77 Reviews)
6.8
Mestek

hello i am a computer engineer,i have masters in computer engineering,i have experience for more than 8 years in arduino and electronics,i can make to u the required RF transmitter and receiver with the indicated dim More

$135 AUD in 2 days
(30 Reviews)
5.5
macroenergy

I am an electronic engineer with 20 years of experience. I've done a lot of projects so far. I use Altium for electronic design. I use the datasheet of ICs to create a library and schematic. I can give you examples if More

$100 AUD in 7 days
(4 Reviews)
2.9
stenniswood

Hello Friend, I read your post and am interested in your project. I am an electrical engineer with 15+ years of automotive experience. I am confident I can get this job done for you. I have design numberous PCB's i More

$225 AUD in 7 days
(1 Review)
2.4
saqib150706

Hello! I am Mechatronics engineer. I have experience working with different microcontrollers, PCBs and integration of sensors. I have read your description and I think it matches my expertise. I would like to work with More

$200 AUD in 5 days
(2 Reviews)
2.3
umg536

Hi there, Being a professional electrical engineer, I can do this project for you. please leave a message on my chat so we can discuss the budget and deadline of the project. Also, have a look at my profile for my rev More

$250 AUD in 6 days
(0 Reviews)
0.0
mustafabugraavci

Hello Employer When I was Electrical engineering student I always did projects like this and I am doing projects like this all the time. If you choose me you'll never regret.

$230 AUD in 12 days
(0 Reviews)
0.0
f3liss

Hello, I am quite new here. I have master degree from EE department in the field of RF electronics and high power circuitry. By having deep experience in PCB design, I believe i can satisfy your project requirements a More

$250 AUD in 7 days
(0 Reviews)
0.0