Analyze a Part Using Abaqus

Closed Posted 5 years ago Paid on delivery
Closed Paid on delivery

I need a part that I've designed for an independent project analyzed using Abaqus FEA software. Analysis must be in Abaqus, as that is the only FEA software I have access to/am familiar with. Attached is a drawing of the part with the relevant geometry and loading.

The torque arm shown in the figure is under horizontal and vertical loads transmitted from a shaft at the right hole, while the left hole is fixed. Young’s modulus = 200 GPa, Poission’s ratio = 0.3 and thickness = 1.0 cm.

Requirements:

(1) Use 4 different element types (CST/LST/Q4/Q8) in Abaqus to find out the maximum von Mises stress and displacements (both u and v) at the point where loads are applied. Use approximately the same number of nodes for each element type and compare the results.

(2) Use Q4 to do a convergence study on vertical displacement at the point where loads are

applied. You can gradually increase the number of elements and see how the displacement

results converge.

Make a formal report for this project. It should include but not limited to:

Part (1)

- Contour plot of deformed geometry

- A table with Von Mises stress results from 4 different element types. (Indicating the number of nodes you used for each element type)

- A table with displacement results from 4 different element types

- Compare the results

Part (2)

- A table with displacement results for different number of elements

- A plot of convergence study (displacement vs number of elements)

- Discussion

Please provide a Microsoft word file and the CAE file.

Engineering Finite Element Analysis Mechanical Engineering Report Writing

Project ID: #18304996

About the project

11 proposals Remote project Active 5 years ago

11 freelancers are bidding on average $111 for this job

ashrafshekh

Hello, Greetings of the day, I have gone through the description & found interesting. I have done many project related to mechanical engineering, 3D modelling, product designing, any kind of simulation, MATLAB, d More

$166 USD in 1 day
(72 Reviews)
6.9
olaideejiwole

I am a Mechanical Engineer with a masters degree in solid mechanics and a product optimization specialist by profession. I have experience in Mechatronic, FEA, Hydraulic actuator, Matlab,3D Modelling, CAD/CAM, AUTOCAD, More

$10 USD in 1 day
(42 Reviews)
5.8
saied2017

Hello I'm Mohamed Saeed. mechanical engineer with high experience in ABAQUS. I have checked your job description and I'm ready to help you

$333 USD in 1 day
(47 Reviews)
5.9
androaiad

Hello dear, I am a M.Sc. Structural engineer. I am expert in structural analysis and FEA using Abaqus. I Checked all the requirements and will provide the required report in the required time. Please check my portfolio More

$30 USD in 2 days
(78 Reviews)
5.9
Kimurayosiko

Dear, I majored in mechanics and have the qualification of Master of Mechanics. And I am a talented Abaqus experts. I have 10 years of experience and good history in FEA using Abaqus. I can do your task well and ac More

$15 USD in 1 day
(15 Reviews)
3.6
zubair22ahmed

Mechanical Engineering Hello Mate, I have done ME in Mechanical Engineering and I would like to help with your project. I have been using ABAQUS and ANSYS for analysis while for 3d modeling I use Solidworks. If yo More

$35 USD in 2 days
(1 Review)
1.2
Mostafazidan2010

I have a master of science in finite element analysis of welding by using Abaqus. Moreover, I have several publications in several international journals related to finite element analysis. I am qualified to perform yo More

$166 USD in 2 days
(0 Reviews)
0.0
jsumanth7

I recently have done similar project in ABAQUS (Design and Analysis of Hexacopter for Agricultural use). The project involves designing of the hexacopter frame in SOLIDWORKS and carrying out Static and Dynamic analysis More

$25 USD in 3 days
(0 Reviews)
0.0
sohrab90

Per my knowledge and experience in finite element analysis and engineering. I assure to deliver the accurate and scientific work done to you. I have experience in and also work as a simulation and analysis engineer fam More

$140 USD in 2 days
(0 Reviews)
0.0